diff --git a/README.md b/README.md
index 5834fd3..b0e8f90 100644
--- a/README.md
+++ b/README.md
@@ -5,34 +5,36 @@ It it's a great starting point to integrate battery with your home automation.
 
 ** I ACCEPT NO RESPONSIBILTY FOR ANY DAMAGE CAUSED, PROCEED AT YOUR OWN RISK **
 
-Features:
-- Low cost (around 20$ in total).
-- Adds WiFi capability to your Pylontech US2000B battery.
-- Device exposes web interface that allows to:
+# Features:
+  * Low cost (around 20$ in total).
+  * Adds WiFi capability to your Pylontech US2000B battery.
+  * Device exposes web interface that allows to:
     * send console commands and read response over WiFi (no PC needed)
     * battery information can be retrevied also in JSON format for easy parsing
-- Easy to modify code using Arduino IDE and flash new firmware over WiFi (no need to disconnect from the battery).
+  * Easy to modify code using Arduino IDE and flash new firmware over WiFi (no need to disconnect from the battery).
 
 See the project in action on [Youtube](https://youtu.be/7VyQjKU3MsU):
-[![See the project in action on YouTube](https://img.youtube.com/vi/7VyQjKU3MsU/1.jpg)](https://www.youtube.com/watch?v=7VyQjKU3MsU)
+[![See the project in action on YouTube](https://img.youtube.com/vi/7VyQjKU3MsU/0.jpg)](https://www.youtube.com/watch?v=7VyQjKU3MsU)
 
-Parts needed:
-- [Wemos D1 mini microcontroller](https://www.amazon.co.uk/Makerfire-NodeMcu-Development-ESP8266-Compatible/dp/B071S8MWTY/).
-- [SparkFun MAX3232 Transceiver](https://www.sparkfun.com/products/11189).
-- Cable with RJ10 connector (some RJ10 cables have only two wires, make sure to buy one that has all four wires present).
-- Capacitors C1: 10uF, C2: 0.1uF (this is not strictly required, but recommended as Wemos D1 can have large current spikes).
+
+# Parts needed:
+  * [Wemos D1 mini microcontroller](https://www.amazon.co.uk/Makerfire-NodeMcu-Development-ESP8266-Compatible/dp/B071S8MWTY/).
+  * [SparkFun MAX3232 Transceiver](https://www.sparkfun.com/products/11189).
+  * Cable with RJ10 connector (some RJ10 cables have only two wires, make sure to buy one that has all four wires present).
+  * Capacitors C1: 10uF, C2: 0.1uF (this is not strictly required, but recommended as Wemos D1 can have large current spikes).
 
 ![Schematics](Schemetics.png)
 
-How to get going:
-- Get Wemos D1 mini
-- Install arduino IDE and ESP8266 libraries as [described here](https://averagemaker.com/2018/03/wemos-d1-mini-setup.html)
-- Open [PylontechMonitoring.ino](PylontechMonitoring.ino) in arduino IDE
-- Specify your WiFi login and password at the top of the file (line 13-14)
-- Upload project to your device
-- Connect Wemos D1 mini to the MAX3232 transreceiver
-- Connect transreceiver to RJ10 as descibed in the schematics (all three lines need to be connected)
-- Connect RJ10 to the serial port of the Pylontech US2000 battery. If you have multiple batteries - connect to the master one.
-- Connect Wemos D1 to the power via USB
-- Find what IP address was assigned to your Wemos by your router and open it in the web-browser
-- You should be able now to connunicate with the battery via WiFi
+
+# How to get going:
+  * Get Wemos D1 mini
+  * Install arduino IDE and ESP8266 libraries as [described here](https://averagemaker.com/2018/03/wemos-d1-mini-setup.html)
+  * Open [PylontechMonitoring.ino](PylontechMonitoring.ino) in arduino IDE
+  * Specify your WiFi login and password at the top of the file (line 13-14)
+  * Upload project to your device
+  * Connect Wemos D1 mini to the MAX3232 transreceiver
+  * Connect transreceiver to RJ10 as descibed in the schematics (all three lines need to be connected)
+  * Connect RJ10 to the serial port of the Pylontech US2000 battery. If you have multiple batteries - connect to the master one.
+  * Connect Wemos D1 to the power via USB
+  * Find what IP address was assigned to your Wemos by your router and open it in the web-browser
+  * You should be able now to connunicate with the battery via WiFi